T200K Online Symphony controller
1,T-200k System features
1.32—256 Gray level,Support software Gamma correction.
2. Support the rules and special-shaped handle.
3. 8 ports output,one port can support 512-1024 pixels.
4. offline (SD card) control and on-line control can be combined
using multiple controllers, the contents of the offline control
program stored in the SD card.
5. Compatible with single line or double line chips.
6. If the controller to the lamps distance can choose photoelectric
isolated transmission and as far as several distances of up to
200-300 M
Note:T-200K Off-line(SD Card) control need to be the first master
controller insert SD card.
T-200 K in the PC software compatible with T-100 K-B
NOTE:1. When T-200k controller control less than 512 lamps the
frame rate can reach 30fps. When T-200k control more than 512 lamps
and less than 2048 lamps the frame rate will slow down
automatically.
2. T-200k must use the new software LedEdit 2012.
2,Support chips:
Chip type | Software code& Controller type | Lamps/(MAX) | Note |
LPD6803,D705,1101,6909, 6912 | T-100K-B-6803 | 8192 | 32 gray level |
LPD8806,LPD8809 | T-100K-B-8806 | 4096 |
|
TM1803,TM1804,TM1809,TM1812 | T-100K-B-TM | 4096 | TM1804 and TM1809 are divided into high and low |
TM1903,TM1904,TM1909,TM1912 | T-100K-B-TM19 | 4096 |
|
UCS6909,UCS6912,UCS7009,UCS5903 | T-100K-B-UCS32 | 4096 |
|
UCS1903,UCS1909,UCS1912 | T-100K-B-UCS256 | 4096 | divided into high speed and low speed |
UCS3903 | T-100K-B-UCS1024 | 4096 |
|
DMX512 | T-100K-B-DMX | 1360/4096 | Compatible with standard DMX512 |
WS2801,WS2803 | T-100K-B-WS | 4096 |
|
WS2811 | T-100K-B-WS2811 | 4096 | divided into high speed and low speed |
DS189 | T-100K-B-DS189 | 4096 |
|
TLS3001,TLS3002,TLS3008 | T-100K-B-TLS | 4096 |
|
P9813 | T-100K-B-P9813 | 4096 |
|
SM16715 | T-100K-B-SM16715 | 4096 | divided into high speed and low speed |
SM16716 | T-100K-B-SM16716 | 4096 |
|
BS0901,BS0902 | T-100K-B-0901 | 4096 |
|
BS0815 | T-100K-B-0815 | 4096 |
|
NOTE:if chip is 256 grade gray level and Single-line IC choose
.When programming choice high speed mode and one interface controls
1024 lamps the play speed can reach 30 frames/s. Double-line IC or
single-line IC with low speed , one interface controls 512 lamps
the play speed can reach 30 frames/s.
3.Appearance picture
4.The meaning of flag
TTL signal(245 signal):
AC IN | Exchange 220V power supply | COM(common port) | GND (ground wire) |
POWER | POWER LIGHT | DAT | Signal |
STATUS | Status light | CLK | The clock line |
SD CARD | SD card slot |
|
|
NOTE:According to TTL signal output,Ground of the controller must
be connected to the lamp’s ground.
5.System architecture figure
Note:The IP address of the computer should be set to:
192.168.60.178
6. wiring diagram:
Note:
1. If the distance between controller and lamps more than 50m we
suggest using differential signal transmission control or
Photoelectric isolated signal transmission control,please read the
manual carefully. Signal lines must be a cable,the best is Super
five kinds of cable.
7. Application scope
LED digital tube,,LED point light source,the exterior light and a
module, pixel screen (dazzle colour screens), high power DMX
lighting.
8.Specific parameters:
Memory card:
Type:SD card(if controlling so many lamps it is best to use the
high-speed SD card.)
Capacity:128MB—2GB
Format:FAT
Store file:*.led
Physical parameters:
Working temperature :-30℃—85℃
Weight:1.35KG
Working voltage:AC220V
Working power:8W
Size:L270mm×W180mm×H55mm
Signal port:3pin connect port
NOTE: T-300K Support online download the effect-file to SD card.
Attention:
T-100K-B outline controller. if many controller be used at the same
time, the first controller must inset a SD card with one file only!
Before copy files to SD card ,The SD card must be formatted as FAT
format.
The SD card in controller can not be hot-swappable, plug the SD
card every time, you must first disconnect the power supply
9. Trouble shooting
Light question 1: controller after electrify, indicator light is
normal, but the lamps no effect change
Answer: the reasons for this are the following:
(1) Please check lamps signal and controller have correct
connection.
(2) If it is meet TTL signal, lamps and lanterns and controller
must altogether, namely the lamps GND (ground) to the GND and
controller (ground) got together.
(3).Please check the effect file of SD card , the selected models
whether current lamps and used the chip consistent.
Question2
After power, the T-1000S ERROR indicator has been flashing without
display output
answer:The ERROR indicator has been flashing means the controller
did not read the card correctly, possible problems:
①SD card is empty, with no effect file.
②The effect file in the SD card and the controller model are not
match, please choose correct controller model in LedEdit and then
re-create the effect file *led.
③SD card did not format to FAT before copy effect files.
④Please check the supply power voltage, the controller can be
individually powered to exclude power reasons
⑤Changing the SD card and then test to exclude the possibility of a
bad SD card
Question 3: The controller is powered on, the indicator is normal,
but the lamps have no effect change
Answer: The reasons for this are as follows:
① Checking if the lamp′s signal line and the controller connected
correctly.
② If be received was the TTL signal,the lamp and the controller
must be common grounding, that means connect the lighting′s and the
controller′s ground wire together.
③ Check if the model chose during making display files on the SD
card match the chips used in the lighting.
Question 4:Controller Connecting to the computer but can’t work
normally.
Answer: 1).The IP address set to 192.168.60.178
2).Check the controller's ip address is 192.168.1.1
3).Check the network cable is connected,Or whether produced in
accordance with the common standards of the network cable.
